200V Class

Rated Input Voltage:

200 - 240VAC + 10%,
Three Phase (3Ø)
50/60Hz + 5%

Rated Input Voltage:

380 - 460VAC, +10%, 3Ø (only)
50/60Hz + 5%.

Rated Output Voltage:

380 - 460V + 10%, 3Ø
Corresponding to supply voltage.

Output Frequency Range:
0.1 - 400 Hz
To operate the beyond 50/60 Hz, 
consult the motor manufacturer 
about the maximum allowable speed

Frequency Accuracy:
Digital command: 
+ 0.01% of the max. frequency
Analog command: 
+ 0.2% (25C + 10C) of the max. frequency

Frequency Resolution:
Digital:     0.1 Hz
Analog:     Max. frequency/4000

V/F Characteristics:
V/F free setting, constant torque, and reduced torque of V/F control.

Overload Capacity:
120%, 30 Seconds
150%, 0.5 Seconds

Acceleration/Deceleration Time:
0.1 - 3600 sec. (linear/curve, accel./decel.), 
Two stage accel./decel. setting available

Braking:
Dynamic Braking - 
Built-in BRD circuit (Optional resistor) for 15, 20 HP only.
External dynamic braking unit (option) for 25 HP & above.
Braking resistor is not integrated in the inverter.
Please install optional braking resistor or dynamic braking unit when large control torque is required.

DC Braking - 
Performs at start; under set frequency at deceleration,
or via an external input (braking force, time and operating
frequency)

Input Signal:
Frequency Setting -
Operator: 
Up(1) and Down(2) keys/value setting keys.
Potentiometer:
Set by potentiometer
External signal: 
DC 0 ~ 10 VDC, 
-10V to +10V  (input impedence 10k ohms), 
4 ~ 20 mA (input impedence 100k ohms)
External Port:
Set by RS485

Forward/Reverse/Start/Stop -
Operator: 
Run key/Stop key  (FW/RV can be set by command)
External signal:
FW RUN/STOP (NO contact), RV set by terminal assignment (NO/NC selection), 3-wire input possible
External Port:
Set by RS485

Intelligent Input Terminals - 
Selection of 5 functions from:
RV (Reverse), CFI~CF4 (Multispeed command), JG (Jogging), DB (External DC braking), SET (Second motor constants setting), , 2CH (Second accel./decel.)
FRS (Free-run stop), EXT (External trip), USP (Unattended Start Protection), 
CS (Change to/from commercial power supply) SFT (Software lock), AT(Analog input selection), RS (Reset), STA (3-wire start), STP (3-wire stop), F/R (3-wire fwd./rev.), PID (PID On/Off), PIDC (PID reset), UP/DWN (Remote-controlled accel.decel.), UDC (Remote-controlled data clearing), SF1-SF7 (Multispeed bit command 1-7), OLR (Overload limit change), and NO (Not selected)

Thermistor Input - 
One terminal

Output Signal:
Intelligent Output Terminal - 
Two NO contacts and one NO-NC combined contact (Selection from: RUN, FA1, FA2, OL, OD, AL, FA3, IP, UV, RNT, ONT and THM)

Intelligent Monitor Output Terminal - 
Analog voltage, analog current, pulse line output

Display Monitor:
Output frequency, output current, scaled value of output frequency, trip history,
I/O terminal condition, input power, output voltage.

Other Functions:
V/F free setting (up to 5 points), frequency upper/lower limit, frequency jump, 
accel/decel curve selection, manual torque boost value and frequency adjustment, analog meter tuning, start frequency setting, carrier frequency setting, electronic thermal free-setting, external frequency output zero/span reference, external frequency input bias start/end, alalog input selection, retry after trip, restart after instantaneous power failure, various signal outputs, reduced voltage start, overload restriction, automatic energy saving.

Carrier Frequency Range:
0.5 - 12kHz

Protective Function:
Over-current protection, overload protection, braking resistor overload protection, over-voltage protection, EEPROM error, under-voltage error, CT(Current transformer) error, CPU error, external trip USP error, ground fault, input over-voltage protection, instantaneous power failure, option 1 connection error, option 2 connection error, inverter thermal trip, phase failure detection, IGBT error, thermistor error

Environmental Conditions:
Ambient Operating: -10 ~ 50ºC
Storage Temperature: -20 ~ 65ºC 
Humidity: 25 ~ 90 % RH(no condensation)
Vibration: 5.9 m/s^2 (0.6G), 10 ~ 55 Hz
Location: Less than 1000 m of altitude or less, indoors (no corrosive gases or dust)

Color:
Blue

Protective Structure:
IP20 (NEMA 1)

Options (cost extra):
EMI filters, input/output reactors, DC reactors, radio noise filters, braking resistors,braking units, LCR filter, multilingual operator with copy function, communication cables,option PCB

Standard Digital Operator:
OPE-SR (Cables (option): ICS-1(1m), ICS-3(3m))

FEATURES:

Automatic Energy Saving Function
With its Automatic Energy-saving Function, the  XKT6 delivers "real-time" energy-saving operation for your fan and pump applications.
      
The function insures that motor operates at minimum current in response to the torque required by the load.

Enhanced Input/Output Terminals
Three relay output terminals are provided as standard for flexible interface to external control systems.
     

Intelligent Input/Output Terminal System
The L300P features an intelligent control terminal system, which allows necessary drive 1/0 functions to be freely programmed. 
Input terminals can be selected for either sink or source type logic.

Easy-to-use Operator Panel
The L300P's operator panel supports various monitoring functions.

Output frequency                    Output terminals status 
Output current                        Converted value of output Rotational direction                                 Output voltage                             
PID feedback value                  Input voltage                           
Input terminals status              Cumulative operation time
Cumulative power-on time        Trip event counter, history
        
Easy-Removable Cooling Fan
Cooling fan(s) and DC bus capacitors can be easily changed in the field. 
A fan ON/OFF function can be activated to provide longer cooling fan life.